本儀器測量原理為直角坐標測量法，即通過X軸、Z1軸傳感器，測繪出被測零件的表面輪廓的坐標點，通過電器組件，將傳感器所測量的坐標點數據傳輸到上位PC機，軟件對所采集的原始坐標數據進行數學運算處理，標注所需的工程測量項目。
The measuring principle of this instrument is the rectangular coordinate measuring method,through X-axis, Z-axis sensor, mapping the surface contour coordinates point of the part under test,data transmission the coordinates point to the upper PC by electrical components.To do the mathematical treatment on the original collected coordinate data by software, marked with the required engineering survey projects.
尺寸：包含水平距離、垂直距離、線性距離、半徑、直徑
夾角：包含水平角、垂直角、夾角
位置公差：包含平行度、垂直度
形狀公差：包含直線度、凸度、圓弧輪廓度
輔助生成：包含輔助點、輔助線、輔助圓
Size: contains the horizontal distance, vertical distance, linear distance, radius and diameter
Angle: horizontal Angle and vertical Angle, Angle
Position tolerance: contains the parallelism and perpendicularity
Shape tolerance: contains the straightness, crown, circular arc profile
Auxiliary generation: contains the auxiliary point, auxiliary line, auxiliary circle
| 項目 Item | 參數 Parameter | |
| 測量范圍 Measurement range | X軸 X axis | 120mm |
| Z1軸 Z1 axis | 24mm | |
| Z軸（立柱） Column (Z-axis ) | 400mm | |
| 直線度 Straightness | 1.2μm/100mm | |
| 線性精度 Linear accuracy | X軸 X axis | ±（1.5+0.025L)μm |
| Z1軸 Z1 axis | ±（1.2+|0.04H|)μm | |
| 水平精度 Horizontal accuracy | ±（1+0.025L）μm | |
| 垂直精度 Vertical accuracy | ±（0.8+|0.03H|)μm | |
| 檢測方法 Detection method | X軸 X axis | 新型數字式傳感器/ 0.2μm |
| Z1軸 Z1 axis | 新型數字式傳感器/ 0.01μm | |
| 驅動速度 Driven speed | X軸 X axis | 4檔，可自定義速度 4 grade, speed is adjustable |
| Z軸（立柱）Column (Z-axis ) | 4檔，可自定義速度 4 grade, speed is adjustable | |
| 測量速度 Measurement Speed | X軸 X axis | 0.1，0.2,0.5,1mm/s 、自定義 |
| 驅動方式 Drive mode | X軸 X axis | 電動 Electric |
| Z軸 Z axis | 電動 Electric | |
| 附件 Accessories | 測針 Probe | 25μm硬質合金針尖 25μm hard metal alloy needle tip 規格：17°單切面 ?4*32 Spec：17°uniplanar ?4*32 上升角度：72° Rise angle：72° 下降角度：88° Drop angle：88° |
| 測桿 Measuring pole | 直徑6mm Diam 6mm | |
| 調整臺 Adjust table | Ｙ向調整、轉角調整 Ｙ direction adjustable, Turn Angle adjustable | |
| 精密正弦平口鉗 Precision sine flat pliers | 鉗口寬 Plier width 50 鉗口深 Plier depth 25 開口度 Opening degree 60 調整角度 Adjustable angle 0-45 | |
技術特點 Technical characteristics
① X、Z1均采用新型數字式傳感器，精度更高
② 大量程設計，杠桿比僅為1:2.2，限度保持了傳感器的原有精度
③ 高剛性高精度直線運動導軌、高精度數字式線性傳感器
④ 采用高速并行數據采集單元，硬件觸發、硬件高速采樣，無延時；足夠密集及穩定的數據源為后期數據處理、計算提供力的保障
① X, Z1 adopt imported new digital sensor, higer precision ;
② Design in a wide range, leverage ratio is 1:2. 2, the maximum keep the original precision of the sensor;
③ High rigidity, high precision linear motion guide rail, high precision digital linear sensor;
④ Using high speed parallel data acquisition unit, high-speed sampling hardware trigger, hardware, without delay. Dense and stable source provide the most powerful guarantee for later data processing, calculation.
軟件系統 Software System
強大的系統功能
軟件兼容winXP、win7、win8系統 Software support XP、win7、win8 system.
軟件支持中英文 Software support Chinese and English language.
快捷自由的頁面布局
軟件增設快捷鍵，方便使用 Software add shortcuts, easy to use
支持將菜單及控制區收起操作，以擴大繪圖區的有效區域面積 Support pack up the menu and control operation, to enlarge the drawing effective area
豐富的數據處理系統
圓弧、線自動識別 Automatic identification of circular arc, the line
擬合可選擇點選或框選 Fitting choice click or marquee
軟件標注與CAD同理 Software similarly marked with CAD
支持連續標注、基準標注、支持任意插入點 Support continuous annotation and datum mark, support any insertion point
支持圖形自由旋轉及坐標自由旋轉 Support the freedom of graphic rotation and coordinate rotation
支持坐標點標注 Support the coordinate points label
捕捉開關打開時，自動生成及捕捉交點、圓心 、線段中點、端點、圓弧交點、中點、切點等特征點
While capture switch is opened, automatically generated and capture the intersection point, circle, line midpoint, endpoint, circular intersection, midpoint, point of tangency feature points, etc
完善的數據保存模式
原始數據自動保存，便于多次標注 Original data automatically saved, facilitate multiple labels
可將測量的圖形結果轉化成DXF格式 Measurement graphic results can be transferred into DXF forma
鏡像功能，可保存標注后文件 The mirror function, can save after standard file.
便捷的控制方式
可對Z1、X軸當前位置進行監控 Can monitor the current position of the Z1, X axis
測量長度可任意設定 Measuring length can be set freely.
具有測針自動接觸、自動抬起、自動回退功能 Needle automatic contact, automatic lift, automatic back.
可以對操作進行無限次的撤銷及恢復操作 The operation can be unlimited undo and restore
SP2000特色的功能
非比例放大：即使在非比例放大的情況下，也能進行正常的角度、圓弧、水平、垂直、線性等標注。
自動標注：在進行批量測量時，測量保存為模板，再次測量導入模板即可完成自動標注，大大提高測量效率。
數據合成：對于類似直槽工件無法一次測量完成，通過擺放角度進行兩次測量，然后通過軟件進行數據合成。
間斷測量：可對工件進行分段編程（采樣間隔、采樣速度），提高客戶測量效率。
| 行程范圍(mm) Measuring Strokes | 外形尺寸(mm) Overall Dimension | 主機重量 (Kg) Machine Weight | ||||
| X | Z | Z1 | Lx | Ly | Lz | |
| 120 | 400 | 24 | 1409 | 802 | 1632 | 350 |
環境要求 Environment Specifications
電 源：AC 220V±5% 50Hz 單獨地線
功率需求：約500W
環境要求：現場溫度：15～25℃、理想溫度：20±2℃
相對濕度：＜85%
室內周圍應無影響測量的灰塵、振動、噪音、氣流、腐蝕性氣體和較強磁場
Power supply： AC 220 v + 5% for 50 hz Seperate groud wire
Power requirements: about 500 w.
Environmental requirements: the temperature: 15 ~ 25 ℃, ideal temperature: 20 + 2 ℃
relative humidity: < 85%
Around the indoor should have no affect the measurement of dust, vibration, noise, air, corrosive gas and strong magnetic field.
部件名稱 項目名稱 數量 備注 Part Name project name Quantity Remarks 主機部分 基礎工作臺 1套 Host part Basic workbench 立柱系統 1套 column 高精度導軌系統 1套 transverse rail 擺臂系統 1套 Z1 Sensor system 運動控制系統 1套 Motion control system 計算機部分 電腦 1套 Computer Computer 打印機 1套 Printer 軟件 1套 Measurement software 配件 測針 1支 Accessories Stylus 調整臺 1套 Adjusting table 精密正弦平口鉗 1套 flat tongs 工具箱 1套 Toolbox 標準件 1組 standard parts
售后服務 After-sale service
質保期：從安裝驗收合格之日起12個月，但不超過發貨之日起15個月。在此期限內因我方原因造成的機器故障，負責免費維修。
質保期外：我公司采取定期回訪與隨時電話咨詢相結合的售后服務制度，力求及時發現并解決用戶使用中存在的困難和問題，為用戶提供技術咨詢。
公司負責為用戶免費提供計量測試技術咨詢服務。
公司以成本價終身為用戶提供設備保修服務。
如公司接到用戶設備故障請求服務電話，24小時響應，如有必要72小時內派技術人員赴現場解決問題。
公司備有備品備件庫，終身負責為用戶以成本價提供備品備件服務。
公司負責以優惠價終身為用戶提供技術升級、改造等售后增值服務。
用戶所在地區如有我公司地區辦事處，其售后技術服務事宜由我公司地區辦事處全面負責。
Warranty Period: Within 12 months from the date of acceptance, but not exceeding 15 months from the date of shipment.
During this period machine failure caused by our side should be maintained free of charge.
Extra Warranty Period: we will take telephone and regular visit to users as after-sale advisory service.
Our company is responsible for the technical advisory services of metrology for user free of charge.
We will provide life warranty services of machine for users with cost price.
If we get telephone service request about equipment failure from users, we will response to the request in 24 hours,
if necessary we will send technical engineer to the customer’s site to solve problems within 72 hours.
We have spare parts in stock, will provide life warranty services of spare parts for users with cost price
We will provide users with lifelong after-sales value-added technical service，such as technical upgrades，retrofit，etc.by preferential prices.
If there is my company’s office in the region of the users, it will fully responsible for the after-sale technical services.
