<tfoot id="qqie6"></tfoot>
<ul id="qqie6"></ul> 
當前位置：廣州藍河電子設備有限公司>>硬度計>> DID-4數顯扭力起子
| Screw tightening control |
| ● DIGITAL TORQUE DRIVER DID-4M |
 |
| (1) Unify the display sectiona frame. It became stronger. (2) Display Measurement Mode, Unit, Etc. on Display Section. (3) Data Output is USB Form. (4) Prepare each button in accordance with operation. Button operation became simple |
| ＊The torque screwdriver is Ergonomiclight weight, yet ruggedly constructed ＊Available in: lb-in, kg-cmN-m ＊Peak, Real TimePeak Down measuring mode (selectable) ＊800 data memory. ＊Programmable HighLow set points with both audible beepGreen/Red LED indicator for uniform torque tightening or GO/NO GO testing ＊Programmable screw tightening counter ＊Programmable Auto Zero function resets unit to zero for easy operation ＊Both CWCCW operation ＊ASCII format output(USB) ＊Runs on internal NiCad batteries (for 12 hours) Auto shut-off after 10 min. of non-use ＊ AC chargercarrying case included. |
| Specification | DID-4 | |
| Measuring range | 0.020 - 4 N-m | |
| 0.20～40 kgf-cm | ||
| 0.20～35 lbf-in | ||
| Accuracy | ± 0.5% (in case of reading 499 or less = last digit +/- 3 reading) | |
| Display | The 4 figures digital display of LCD | |
| The measurement direction | CW-CCW (rightleft) | |
| Measuring mode | P-P Peak | Holding Peak Load Value |
| T-R Track | Showing Real time torque value ( Used for Zero-Adjustment ) | |
| P-D Peak down | Holding Load Value at the moment to change from upward to downword | |
| C Real-time output | Load torque value is outputted every about 1/ 160. | |
| Decision function | Setting of torque value | Programmable HighLow setpoints with both audible beepGreen/Red LED indicator for uniform torque tightening or GO/NO GO testing |
| The Maximum, the minimum,the average value | Displays, memoryoutput the data number, the maximum, the minimum,the average value of the measured value to 30 data. It can save by a maximum of 10 channels. | |
| Data spec. | Data transfer | ASCII format (Baud rate : 19200) When outputting data,the cable(USB miniB) is needed. |
| Data memory | 800 data / ten channels data | |
| A setup of the number of counts | One to 99 count (count in a direction with a bundle) | |
| Power supply | Ni-Cd chargeable battery 1.2V×4cells 600mAh | |
| Auto power save | 10 minutes no use, automatically switch off. | |
| Charging time | From empty - less than 5hours | |
| Continunous working time | 12 hours | |
| Bit /Socket part | HEX6.35 | |
| Weight | about 400g | |
| Attachment | Bit?。ǎ。＃薄。＃病?/td> | |
| Accessories (one piece each) | Dedicated AC/DC Adaptor (Charger),100～230VAC | |
| An inspection report, a proofreading certificate, a traceability system figure | ||
請輸入賬號
請輸入密碼
請輸驗證碼
以上信息由企業自行提供，信息內容的真實性、準確性和合法性由相關企業負責，儀表網對此不承擔任何保證責任。
溫馨提示：為規避購買風險，建議您在購買產品前務必確認供應商資質及產品質量。
儀表網