HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀廠家@新聞快訊,陶瓷磚平整度、直角度、邊直度綜合測定儀,陶瓷磚無釉面耐磨測定儀,陶瓷磚凍性試驗機,陶瓷磚抗熱震性測定儀,陶瓷磚厚度測量儀
本公司3月12號09點07分報道：HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀廠家@新聞快訊
（/c149978/products/d.html）
產品簡介
YI、HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀簡介：
HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀適用于測定各種墻面磚、地面磚尺寸及形狀特性之儀器，其所測參數包括面磚的邊直度、直角度、平整度（中心彎曲度、邊彎曲度、翹曲度）等幾項指標。本產品符合：GB/T3810.2 ，ISO?10545-2 《陶瓷磚－尺寸和表面質量的檢驗》的要求。
Brief introduction of hbtcy-02 ceramic tile flatness, right angle and edge straightness comprehensive tester:
Hbtcy-02 comprehensive measuring instrument for flatness, right angle and edge straightness of ceramic brick is suitable for measuring the size and shape characteristics of wall tiles and floor tiles. The parameters measured include the edge straightness, right angle, flatness (central bending, side bending, warping degree) and other indexes of the tiles. This product meets the requirements of GB / t3810.2, ISO? 10545-2 "ceramic tiles - Inspection of dimensions and surface quality".
技術參數
二、HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀技術參數：1、測量精度:±0.1mm
2、測量范圍： 300×300～800×800mm，300×300～1000×1000mm（用戶選配）
3、標準板客戶選購（選購件）?
4、根據用戶要求可選用數顯表。
5、外形尺寸：1200X1220X200mm
6、整機重量：95Kg
三、HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀檢測步驟：每種類型的磚取10塊整磚進行檢測。
1、邊直度與直角度的檢測：
當磚放在儀器的三個支承銷上時，使定位銷靠近被測邊，離測量邊每個角的距離為5mm，邊直度量表的測桿調整至被測邊的處；直角度量表的測桿應在離測量邊的個角5mm處。
將合適的標準板地置于
儀器的測量位置上，調整量表的讀數至合適的初始值。
取出標準板，將磚的正面恰當地放在儀器的定位銷上，分別記錄邊處和離角5mm處的量表讀數，如果是正方形磚，轉動磚試樣，得到4次測量值。每塊磚都重復上述步驟，如果是長方形磚，分別測量長邊和寬邊的邊直度和直角度。測量精度到0.1mm。
2、平整度的檢測：
將相應的標準板地放在3個支承銷上，每個支承銷的中心到磚邊的距離為10mm，中心彎曲度量表座杠桿觸頭應在磚中心位置，翹曲度量表座杠桿觸頭應在磚被測角離磚邊10mm處，調節彎曲度和翹曲度量表的讀數至合適的初始值。
取出標準板，將磚的釉面或合適的面朝下置于儀器上，分別記錄每個量表的讀數。如果是正方形磚，每塊試樣得到4個測量值，每塊磚都重復上述步驟。測量精確到0.1mm。
Testing steps of hbtcy-02 ceramic tile flatness, squareness and edge straightness comprehensive tester:10 whole bricks of each type are tested.
1. Detection of edge straightness and right angle:
When the brick is placed on the three supporting pins of the instrument, make the locating pin close to the side to be measured, and the distance from each corner of the measuring side is 5mm. The measuring rod of the side straight measuring meter shall be adjusted to the center of the side to be measured; the measuring rod of the right angle measuring meter shall be 5mm away from the measuring side.Put the appropriate standard plate on the measuring position of the instrument accurately, and adjust the reading of the gauge to the appropriate initial value.
Take out the standard plate, place the front face of the brick on the positioning pin of the instrument properly, record the meter readings at the center of the edge and 5mm away from the angle respectively, if it is a square brick, rotate the brick sample, and get the measured values for 4 times. Repeat the above steps for each brick. If it is a rectangular brick, measure the straightness and right angle of the long side and the wide side respectively. The measurement accuracy is 0.1 mm.
2. Flatness detection:
Put the corresponding standard plate on three supporting pins accurately, the distance between the center of each supporting pin and the brick edge is 10 mm, the lever contact of the center bending gauge seat should be in the center of the brick, and the lever contact of the warping gauge seat should be 10 mm away from the brick edge, and adjust the readings of the bending and warping gauges to the appropriate initial value.
Take out the standard board, put the glaze or appropriate face of the brick down on the instrument, and record the reading of each meter. If it is a square brick, four measurements are obtained for each sample, and the above steps are repeated for each brick. The measurement accuracy is 0.1 mm.
注意事項
四、HBTCY-02型陶瓷磚平整度、直角度、邊直度綜合測定儀注意事項：1、放置試樣或標準板時，應輕拿輕放，不要用力過大，以免影響檢測結果。
2、儀器應安放在平穩且干凈的基面上，保持儀器各部位的清潔，并不定期在儀器各部位表面抹擦少量機油以防銹蝕。
3、標準版另配。
主營產品：土工檢測儀器,防水材料檢測儀器,陶瓷磚檢測儀器,水利水電粗粒土系列,瀝青儀器檢測儀器
Main products: geotechnical testing instrument, waterproof material testing instrument, ceramic brick testing instrument, water conservancy and hydropower coarse-grained soil series, asphalt testing instrument
