YX、YXC型電接點壓力表 YX、YXC Series Electrical Contact Pressure Meter 簡介 電接點壓力表適用于測量對銅合金無腐蝕、無爆炸危險、非結晶的各種液體、氣體等介質的壓力。儀表經與相應的電氣器件配套使用，可達到對被測壓力系統實現預先設定的zui大或zui小壓力值的雙位自動控制和發信（報警）的目的。 儀表具有測量控制功能，可任意設定上、下控制壓力值，動作穩定可靠，在石油、化工、電站、冶金等工業企業及機電設備上廣泛配套使用。 本公司生產的電接點系列包括括磁助電接點、耐震電接點、不銹鋼電接點、隔膜電接點、氨用電接點等，可全面滿足使用條件的要求。 Brief Introduction: Electrical contact pressure meter is applicable to measure pressures of various such mediums as non- crystallized liquids or gases without danger of explosion that has no corrosive action on copper alloy. This instrument, if used with corresponding electrical devices in supporting set, may achieve the purposes of two-digital automatic controlmessage sending alerting, which show pre-set max. or min. pressures of the tested pressure system. This instrument has measuringcontrolling function, which enables arbitrary setting of upper and/or lower values of pressure control. With its reliable action, it is widely used supporting device in electromechanical equipments in such industries as petroleum, chemical industry, power station,metallurgy. Electrolysis point series produced by this company include: magnet-booster electric contact, shock resistance electric contact, stainless steel electric contact, diaphragm electric diaphragm, electric contact for ammonia, etc., fully satisfying requirements of applied conditions. 構成示意圖 主要技術參數 - 精確度：1.6級，2.5級
- 觸電功率：YXC磁助式為1A、10VA， YX 直接作用式為0.7A、30VA
- zui高工作電壓：AC380V 、DC220V
- 控制方式：上、下限、雙上限、雙下限等控制形勢。
- 使用環境：-40℃～70℃，相對濕度不大于85%
Principal technical parameters - Precision : 1.5, 2.5 grades
- Electric shock power: 1A, 10VA, YX for YXC magnet assisting type 0.7A,30VA for direct action type
- Highest working voltage: AC380V
- Control style: upper or lower limit, double upper limit, double lower limit, or other control forms
- Environmental condition in use: -40～70℃, relative humidity less than 85%
結構原理 儀表由測量系統、指示裝置、電接點裝置、外殼、調節裝置及接線盒等組成。 當被測壓力作用于彈簧管時，其末端產生相應的彈性變形——位移，經傳動機構放大后，由指示裝置在度盤上指示出來。同時指針帶動電接點裝置的活動觸點與設定指針上的觸頭（上限或下限）相接觸的瞬時，致使控制系統接通或斷開電路，以達到自動控制和發信報警的目的。 在電接點裝置上裝有可調節的*磁鋼，可以增加接點吸力，加快接觸動作，從而使觸點接觸可靠，消除電弧，能有效地避免儀表由于工作環境振動或介質壓力脈動造成觸點的頻繁關斷。所以該儀表具有動作可靠、使用壽命長、觸點開關功率較大等優點。 Configuration principle This instrument consists of measuring system, indicating device, magnet-assisted electric contact device, outer housing, adjusting device,junction box, etc. When the pressure acts on the spring pipe, corresponding elastic deformation or displacement occurs at the pipe end accordingly, which is amplified through running geardisplayed in indicating devices dial as the pressure being tested. Meanwhile, indicating needle makes the armature contact of the electric contact devicethe contactor superior limit or lower limit fixed on needle contact together instantaneously, which causes the controlling system switches on or off, for the purpose of automatic controlalert by sending message. A piece of permanent magnetic steel is fixed on the electric contact signaling needle of the electric contact device, so as to reinforce the magnetism of the contactorspeed up the contact action. This may ensure reliable contact of the contactors, to eliminate electric arc,to avoid such frequent switch-on/off of the contactors caused by the working environment, vibration, or medium pressure pulse of the instrument. This instrument has a lot of advantages, including reliable action, long-term life span of usage, greater power of contact switch,so on. | 
服務咨詢：
儀表技術群：
